Shenzhen Southern Machinery - SMT / THT equipment, PCB separators and spare parts since 2011
Southern Machinery Southern MachinerySMT / THT equipment and spare parts
X3100 ROI - true stock in MES

X3100 X-Ray Counter ROI: 99.99% Accuracy & MES Sync
by Southern Machinery

Four reels, one X-ray shot, 6 - 10 seconds (chip 0201). The X3100 counts through the closed tape, reads every reel barcode, writes the quantity to your MES, ERP or WMS and prints the new label. Put your own reel volume and labour cost into the calculator and see when it pays back.

X3100 offline X-ray counter, front view with tray and keyboardX-ray image of a reel counted at 1,522 partsCounting software main screen: barcodes read per tray, counts over the X-ray image, records and log
99.99 %
Counting accuracy, brochure 0201 example
6 - 10 s
Per four reels, chip 0201 (offline X3100)
MES
ERP / WMS sync, every barcode read by a 20 MP camera
01005
Smallest part size it can count
Shenzhen manufacturer since 2011Payback worked out from your numbersMES / ERP / WMS data outputTXT, CSV, XLS daily recordsRemote set-up and training in English
The short answer

Where the X3100 return on investment comes from

The Smart EMS X3100 from Southern Machinery is an X-ray component counter that turns reel counting from a manual job into a 6 - 10 second machine cycle for four reels (chip 0201). Its return on investment comes from three places you can measure in your own plant: the labour hours spent counting reels by hand or by tape-wheel counter, the line stops and emergency buys caused by wrong reel quantities, and the time lost reconciling MES or WMS stock with the shelf. The X3100 counts through the closed tape down to 01005 parts with 99.99 % accuracy in the brochure's 0201 example, a 20-megapixel camera reads every barcode on the reel label, and the quantity is written against the reel ID to MES, ERP or WMS while a new label prints. Southern Machinery publishes no savings figure; the calculator on this page uses only your inputs.

Quick facts

Product
X-ray SMD component counter with MES / ERP / WMS link
Maker
Shenzhen Southern Machinery Sales and Service Co., Ltd.
Accuracy
99.99 % (brochure, 0201 example); trial count on your reels recommended
Speed
6 - 10 s per 4 reels offline; 9 - 15 s per reel inline (chip 0201)
Data sync
Reads all reel barcodes, writes quantity per reel ID, prints new label
Records
Daily files, no capacity limit, TXT / CSV / XLS
ROI basis
Your reels per month, hand-count minutes and labour cost - no assumed saving
Price and lead time
Quoted per order - not published
The cost of a wrong count

Three costs that disappear when every reel is counted

A wrong reel quantity costs nothing on the day it is written. It costs a lot on the day a feeder runs empty, a buyer pays for an express shipment or an auditor asks for the real stock. These are the costs the X3100 attacks.

01

Counting labour you pay for every shift

Hand counting and tape-wheel counters handle one reel at a time and the tape has to be pulled through. The X3100 counts four reels in one shot without opening them, so the hours move from counting to useful work.

02

Line stops and emergency buys from false stock

Returned reels keep their original label quantity. MES plans the next job on numbers that are no longer true and the shortage appears at the machine, in the middle of a job.

03

Reconciliation work between MES and the shelf

Cycle counts, customer consignment and year-end inventory need a quantity per reel ID. When the counter writes the number to MES the moment it counts, the spreadsheet work and the arguments go away.

The return comes from the reels you count every day, not from the machine on the floor.

How it works

Four steps from reel to correct label

Each step follows the X3100 brochures and the English operation manual. The data step is where the MES sync happens: quantity and reel ID leave the machine together.

Verified source
LOAD 4 REELS

Load up to four reels

The tray slides out; place one to four reels (or trays, tubes, bags) in the marked positions and press both start buttons. Single-reel and multi-reel modes are selectable.

X-RAY SHOT

X-ray image in one shot

The tray goes in, the closed X-ray tube switches on and the 3072 x 3072 pixel flat panel takes one image of all reels through tape and cover.

COUNT + READ

Count and read the labels

Software counts the parts on every reel and the 20-megapixel camera reads all barcodes on the labels, matching quantity to reel ID automatically.

MES SYNC + LABEL

Sync MES and print

With the MES / ERP button active, the result is sent to MES, ERP or WMS, saved in the daily records (TXT / CSV / XLS) and printed as a new 60 x 40 mm label for each reel.

Daily counting cycle - concept viewConcept view

Reels come back from the line or arrive at goods-in
→
Load up to 4 reels, press both start buttons
→
X-ray image, count, barcode read
→
Count plausible and every label read?No → Check part type, brightness setting or barcode type, then recount
→
Yes · Quantity synced to MES, new label printed, reel released
Match the ROI to your volume

Choose the version that pays back at your reel flow

Both versions use the same X-ray tube, flat panel and counting software. The offline X3100 suits most warehouses; the Inline version removes the operator when the reel flow is high enough to justify it.

X3100 offline X-ray counter
Offline

X3100 offline X-ray counter

Stand-alone cabinet for goods-in, the kitting room or the line-side store. The operator loads the tray and applies the printed label.

  • Up to 4 reels per shot, 6 - 10 s (chip 0201)
  • Reels 4 - 17 inch, 1 - 92 mm high, up to 10 kg
  • X-ray inspection mode for hidden faults
Evidence: X3100 brochure and operation manual
X3100 Inline automatic counting system
Inline

X3100 Inline automatic counting system

Feeding, X-ray counting, labelling and unloading in one line, built for a smart warehouse or reel storage tower.

  • Automatic loading, counting, labelling and unloading
  • 9 - 15 s per reel, reels 7 - 17 inch, 1 - 80 mm
  • Label placed on a blank area with 360° visual positioning
Evidence: X3100 Inline brochure and video
Numbers to gather before you calculate
For your ROI case

Numbers to gather before you calculate

Five facts make the payback calculation and our proposal realistic.

  • Reels counted or returned per month
  • Minutes per reel for today's counting method
  • Your MES / ERP / WMS and label format
Plus line-stop history caused by wrong stock, if you track it
Specification

Specification with sources

Values for the offline X3100 unless the row says Inline. Every row names the document it was read from and carries an evidence label; where the brochure and the English operation manual differ, the row is marked To be confirmed.

ParameterValueSourceEvidence
X-ray tubeClosed type, 80 kV (limited to 50 kV), 0.01 - 0.089 mAX3100 brochure; operation manual chapter 6Verified source
Spatial resolution30 µmX3100 brochureVerified source
Flat panel detectorDigital flat panel, 3072 x 3072 px, 427 x 427 mmX3100 brochure; operation manual chapter 6Verified source
Imaging accuracy139 µmX3100 brochureVerified source
Counting speed6 - 10 s per 4 reels (chip 0201)Brochure and operation manual 6; one brochure table states 6 - 8 sTo be confirmed
Cycle time≤ 10 s per countX3100 brochureVerified source
Counting accuracy99.99 % (0201 example)X3100 brochure and operation manual 6 - verify on your own reelsTo be confirmed
Smallest part01005X3100 brochureVerified source
Barcode camera20 megapixel, reads every label on the reelX3100 brochure; operation manual 7Verified source
Barcode misread rate≤ 0.01 % (0201 example)X3100 brochureTo be confirmed
Reel diameterUp to 430 mm (4 - 17 inch)X3100 brochure; operation manual 6Verified source
Reel height1 - 92 mmX3100 brochure; operation manual 6Verified source
Max. load weight≤ 10 kgX3100 brochureVerified source
ModesSingle reel or up to 4 reels at once; auto QR / barcode scan; MES / ERP buttonOperation manual 9.4Verified source
RecordsSaved per day, no capacity limit, TXT, CSV, XLSX3100 brochureVerified source
Operating systemWindows 11X3100 brochure; operation manual 6Verified source
PowerAC 110 - 220 V, 50 - 60 Hz, 1200 WX3100 brochure; operation manual 6Verified source
Radiation test< 1 µSv/hX3100 brochure; operation manual 6Verified source
Safety circuitsDoor interlocks 1 and 2, double safety circuit, over-voltage / over-current protection, emergency stop, anti-pinch sensorOperation manual 3 and safety chapterVerified source
Machine size949 x 1456 x 1934 mm with printer (brochure); 950 x 1460 x 1960 mm (operation manual)Brochure and operation manual 6 differ - confirm per orderTo be confirmed
Machine weight450 kgX3100 brochure; operation manual 6Verified source
Inline speed9 - 15 s per reel (chip 0201), ≤ 15 s per countX3100 Inline brochureVerified source
Inline size and weight3087 x 1194 x 1957 mm (4366 x 1488 x 1957 mm with cart), 1500 kgX3100 Inline brochureVerified source
X-ray inspection modeLive X-ray view of assemblies, one-click switch back to countingSouthern Machinery X3100 videoConcept view
Versions

X3100 offline or X3100 Inline

The two versions share the X-ray tube, flat panel and counting software. These are the points where they differ; your daily reel volume and floor space decide which one fits.

Status: version chosen per order from your volume and layout
PointX3100 offlineX3100 InlineHow to chooseStatus
HandlingOperator loads up to 4 reels, two-hand startAutomatic loading, counting, labelling, unloadingCount reels per shift and the labour you want to free.By version
Counting time6 - 10 s per 4 reels (chip 0201)9 - 15 s per reel, without an operatorCompare with your peak return volume after each shift.By version
Reel diameter4 - 17 inch, up to 430 mm7 - 17 inch, up to 430 mmSmall 4-inch reels go to the offline version.By version
Reel height1 - 92 mm1 - 80 mmMeasure your thickest reels and trays.By version
LabellingLabel printed, applied by the operatorLabel applied to a blank area, 360° visual positioningSend your label layout and where it must sit.By version
Footprint734 x 1456 x 1934 mm; 949 mm long with printer3087 x 1194 x 1957 mm; 4366 x 1488 mm with cartSend a floor plan with doors and aisles.By version
Weight450 kg1500 kgCheck floor load and the route into the building.By version
PackagesReels, trays, tubes, bags, loose partsReels, automatic flowTrays and loose parts are counted on the offline version.By version
Learn it in 30 minutes

A 30-minute study route for the warehouse lead who owns the counter

Adapted from Southern Machinery's learn-SMT-in-3-hours training method: one question per block, a completion check at the end of each, and every value tied to the X3100 manual. It does not replace the manual or the installer's training.

0 - 5 min: How X-ray counting works

The tube sends X-rays through the reel; metal leads and terminations absorb more than tape and plastic, so each part shows as a dark mark on the flat panel image. Software counts the marks; the camera reads the labels.

Check: explain why the reel never has to be opened.

5 - 10 min: Safety first

The X3100 is an X-ray device. Only trained staff operate it, the door is never opened while X-ray is on, interlocks and warning labels stay in place, and the beryllium tube window is never touched.

Check: name the two conditions that stop X-ray at once.

10 - 18 min: Start-up and a first count

Main power, PC power, release the emergency stop, start the counting software and log in as operator. Choose print, auto barcode scan and single or multi-reel mode, press start, load the reels and press both start buttons.

Check: run one four-reel count and apply the labels.

18 - 26 min: Reading the result

Compare the count with the label quantity and the reel history. A count that looks wrong usually means a brightness setting, an unusual package or a barcode type not set; the manufacturer account handles settings.

Check: list three reasons a count or barcode read can fail.

26 - 30 min: Shut-down and care

Close the software (the tray returns), shut down the PC, press the emergency stop and switch off the main power. Keep the cabinet clean and dry and check the safety lock every day.

Check: shut the machine down in the right order.

Fault-to-check sequence

Start with a safe state and stop at the first point you are not authorised for.

  1. Observed symptom: note the reel ID, part type, mode and what the screen shows.
  2. Safe state: stop X-ray, let the tray return and keep the door closed until X-ray is off.
  3. Software first: flat panel or X-ray init failure usually means the last session did not close - restart the software.
  4. Settings second: wrong counts - adjust brightness; no barcode read - set auto scan and the right code type; printer - check 60 x 40 mm labels, ribbon and template.
  5. Confirmed and authorised: recount and record. Not confirmed: tag the machine and contact Southern Machinery service.

Maintenance card - X3100

Verified source
  • Keep the inside and outside of the cabinet free of dust, water and oil.
  • Check every day that the safety lock and interlocks work.
  • Check that power and ground connections are tight; the cabinet must be earthed.
  • Check that every axis moves smoothly and the limit switches work; clean and re-oil the guide rails once a month.
  • Keep 5 cm free at the fan exhausts and never drill the cabinet.
ROI calculator

Calculate the X3100 payback from your own numbers

Every figure comes from you; the page assumes no saving. Enter how many reels you count per month, how many are counted by hand or by tape-wheel today, how long that takes and what an hour of labour costs. Add the quoted price to see the payback period.

X3100 counting ROI estimate

All inputs are yours. Nothing is sent anywhere.

Leave blank until you have a quotation.
Counting hours freed per month—
Labour cost freed per month—
X3100 operator cost per month—
Net counting value per month—
Payback
—
A planning aid only. It counts labour alone; line stops avoided and MES reconciliation time are extra value you can add from your own records. Results depend entirely on your inputs and are not a performance claim by Southern Machinery.
Videos

Watch the X3100 count, sync and label

The new English promo and Shorts, Southern Machinery X3100 clips and two related X-ray counters. Click a card to play it here.

X3100 X-ray counter: count, sync MES, print (English, 2 min)
2:08

X3100 X-ray counter: count, sync MES, print (English, 2 min)

Pain points, the four-reel count, label and MES link, inspection and the Inline version, with English subtitles.

X3100 in 40 seconds (vertical Shorts)
0:39

X3100 in 40 seconds (vertical Shorts)

The four-reel X-ray count and MES label in a 9:16 clip for mobile viewers.

X3100 X-ray counter in one minute
0:17

X3100 X-ray counter in one minute

Loading reels and counting four at once.

X3100 X-ray counter with inspection
1:18

X3100 X-ray counter with inspection

Inspection mode finds broken wires, then one click returns to counting.

X3100 counting, label printing and MES link
1:32

X3100 counting, label printing and MES link

From reel to printed quantity label and MES record.

X3100 Inline automatic counting system
0:48

X3100 Inline automatic counting system

Robot loading, X-ray counting, labelling and NG outlet.

ADL100 automatic X-ray component counter
6:31

ADL100 automatic X-ray component counter

A related Southern Machinery X-ray counter.

AX6000 SMD X-ray chip counter
1:34

AX6000 SMD X-ray chip counter

A related Southern Machinery X-ray counter.

Open the full video board

Catalogues

Southern Machinery counting documents

Matched from the Southern Machinery product catalogue board: related X-ray counters, the X-ray inspection machine and our counting machines. The X3100 brochure and manual are sent on request.

PDF

SMD X-ray chip counter AX6000

Related X-ray counter brochure.

Open
PDF

ADL100 X-ray SMD counter

Related automatic X-ray counter brochure.

Open
PDF

SM-X3000A X-ray inspection machine

Dedicated X-ray inspection for BGA, voids and solder joints.

Open
PDF

S-CC200 automatic SMT component counter

Wheel-type counter for single reels.

Open
PDF

S-902 automatic SMD counter

Compact automatic counter brochure.

Open
PDF

SMZ-901 SMD components counter

Entry-level reel counter brochure.

Open

Open the full catalogue board

Insights

Eight notes on counting ROI and MES-true stock

Long-form notes for warehouse leads, material planners, finance and SMT managers who need the reel number in MES to be true and the counter to pay for itself.

ARTICLE 01What a Wrong Reel Quantity Really Costs

Price the line stop, the express buy and the recount before you price the counter.

Full articles are in English. The summary above carries the argument in your language.

At 10:15 on a Tuesday the placement line stopped for a 0402 resistor. MES showed 4,200 parts on reel R-88317. The reel on the shelf held 310. Forty minutes later the line restarted with a reel borrowed from another job, and the buyer was already booking an express shipment.

Nobody puts that morning on the counter's cost sheet, yet it is the biggest line on it. A wrong reel quantity costs nothing when it is written and a great deal when it is discovered: idle line time, a changeover nobody planned, a premium freight invoice and an hour of people searching shelves. The usual suspect is the buyer or the feeder. The real cause is a returned reel that went back to stock with its original label.

Before you price any counting method, price one wrong count. Write down the last three shortages that appeared at the machine while the system showed stock: minutes the line stood, what the line hour costs you, any express freight and the people involved. Divide by the number of months it covers. That figure is the cost of trusting uncounted reels, and it belongs in every ROI discussion.

The Southern Machinery X3100 attacks the cause instead of the symptom. Up to four returned reels go on the tray, one X-ray shot counts every part through the closed tape in 6 to 10 seconds for 0201 chips, the 20-megapixel camera reads the reel barcode and the true quantity is written to MES while a new label prints. The reel goes back to the shelf with a number that is true.

Keep the shortage log running. Every month, add any stop caused by false stock and compare it with the months before the counter. When the column stays empty, you have a second ROI figure that sits on top of the labour saving.

Send us your shortage log, reels returned per month and the MES you use at info@smthelp.com or on WhatsApp +86 13602562576. We reply with the right X3100 version and what our engineers need to prepare the data link.

ARTICLE 02Measure Your Counting Labour in One Week

A tally sheet at the return shelf gives the only ROI input that matters.

Full articles are in English. The summary above carries the argument in your language.

Every evening a warehouse clerk sits at the return shelf with a tape-wheel counter, pulling one reel after another through it while the night shift waits for kits. Ask how long it takes and the answer is usually a shrug.

That shrug is why most counter purchases stall. Without a measured minutes-per-reel figure, the ROI case is a guess, and finance rejects guesses. Estimates also err on the low side: they forget the walk, the search for the reel ID, the handwritten label and the correction in the system afterwards.

Measure it for one normal week. Put a tally sheet at the return shelf and the goods-in desk: reel ID, start time, end time, method (hand, tape wheel, scale), and whether the system was updated. At the end of the week you have reels per day, minutes per reel and the share counted at all. Those three numbers are the core inputs of any payback calculation.

Those inputs go straight into the calculator on this page, next to the X3100's own handling time: loading up to four reels, pressing both start buttons and applying the printed labels. The count itself is one X-ray shot of 6 to 10 seconds for four reels of 0201 chips, and the quantity is written to MES without typing.

Repeat the tally for one week every quarter after installation. It shows whether reels are bypassing the counter, whether new packages slowed it down and how much time moved from counting to kitting.

Send your week of tally data, the reel sizes you count and your MES to info@smthelp.com or WhatsApp +86 13602562576, and we will check the calculation with you.

ARTICLE 0399.99 Percent Accuracy: How to Test It on Your Own Reels

A brochure figure becomes your figure with a twenty-reel trial.

Full articles are in English. The summary above carries the argument in your language.

A quality manager reads 99.99 % accuracy on a brochure and asks the obvious question: on whose parts? It is the right question, and the answer should come from your own reels, not from a sales call.

Accuracy figures are always measured on an example. For the X3100 the brochure and the operation manual state 99.99 % with 0201 chips, and a barcode misread rate of no more than 0.01 % in the same example. Your mix may include clear-tape LEDs, large connectors in deep tubes or dense 01005 reels. A figure that holds for 0201 is a strong start, not a promise for every package.

Run a twenty-reel trial. Pick reels that represent your hardest cases: the smallest parts, the densest reels, a partly used reel, a tray and a tube. Count each one by a slow reference method first, record the reference number, then count it by X-ray. Compare reel by reel, note any difference and its cause.

The X3100 makes the trial practical: four reels per shot, results shown over the X-ray image, the barcode read beside each count and every result saved in daily TXT, CSV or XLS records. Where a count looks wrong, the manual points to brightness, part type or barcode type settings, which our engineers set with you.

Keep a monthly spot check after go-live: five random reels counted by reference and by X-ray. The record turns the brochure figure into your figure and tells you early when a new package needs a setting.

Ask for a trial count. Send your hardest part numbers and package types to info@smthelp.com or WhatsApp +86 13602562576 and we will arrange it with you.

ARTICLE 04MES Sync Starts at the Label, Not at the Server

The reel ID and the quantity must leave the counter together.

Full articles are in English. The summary above carries the argument in your language.

The IT team connects the counter to MES, the first week looks fine, and then the planners notice quantities landing on the wrong reels. Nobody touched the server. The problem started at the label.

MES sync is only as good as the link between a quantity and a reel ID. If a clerk types the ID, picks the wrong line on a list or sticks the new label on the neighbouring reel, the database becomes precise and wrong. Interface specifications rarely mention the physical moment when the label leaves the printer.

Treat the reel ID and the quantity as one event. The rule: the same machine that counts must read the ID, and the new label must be applied before the next reel is touched. Agree with IT which barcode fields are read, what file or interface receives them and what the printed label shows.

The X3100 is built around that event. Its 20-megapixel camera reads all barcodes on the reel label, the software matches each count to its reel, and with the MES / ERP button active the result goes to MES, ERP or WMS. The label prints on sensing as each reel is removed, which is why the manual asks operators to take reels out one at a time.

Audit the link weekly: pick ten reels in stock, scan the label and compare the quantity with MES. Any mismatch gets a cause written beside it - typing, bypassed counter, label on the wrong reel.

Send a photo of your current reel label and the name of your MES, ERP or WMS to info@smthelp.com or WhatsApp +86 13602562576. We agree the fields and label layout before shipment.

ARTICLE 05Hand Count, Tape Wheel or X-ray: Comparing Cost per Reel

Minutes per reel times reels per month decides the method.

Full articles are in English. The summary above carries the argument in your language.

A plant manager has three options on the table: keep hand counting, buy another tape-wheel counter, or move to X-ray. The prices are different, so the comparison usually stops at price. It should start at cost per reel.

Purchase price hides the real cost because it ignores volume. A cheap method that takes several minutes per reel becomes expensive at thousands of reels a month, while a more expensive machine can cost less per reel once the volume is there. Moisture-sensitive packs add a hidden cost: every opened bag adds exposure time.

Compare methods on one line: minutes per reel times reels per month times labour cost per hour, plus the cost of errors each method leaves behind. Do it for your current method and each alternative, using measured minutes, not brochure seconds alone, because loading and labelling take time too.

For the X3100 the counting step is one X-ray shot of 6 to 10 seconds for four reels (chip 0201), without opening tape, bag or dry pack, plus the operator's loading and labelling time. Trays, tubes, bags and loose parts are counted on the same tray, and the result goes to MES automatically, which removes the typing step the other methods need.

Recalculate when volume changes. A new customer, a second line or a year-end audit can move the break-even between methods, and the calculation takes five minutes with the inputs you already keep.

Send your current method, minutes per reel and reels per month to info@smthelp.com or WhatsApp +86 13602562576 and we will put the comparison side by side with you.

ARTICLE 06Building the Payback Case Finance Will Sign

Use your own numbers, keep the labour case separate from the upside.

Full articles are in English. The summary above carries the argument in your language.

The finance director reads the counter proposal and circles one sentence: 'expected savings 60 %'. Where does that come from? Nobody can answer, and the proposal goes back into the drawer.

Payback cases fail when they borrow numbers. Supplier percentages, industry averages and best-case scenarios look generous to the buyer and suspicious to finance. Mixing hard savings with possible upside in one figure makes the whole case look soft.

Build the case in two layers. Layer one is labour only: measured reels per month, measured minutes per reel, your labour rate, minus the operator time at the new machine, against the quoted price. Layer two lists the upside separately with your own records: line stops from false stock, express freight, audit hours. Finance can approve on layer one and treat layer two as a bonus.

The calculator on this page follows that structure for the X3100. It takes only your inputs - reels counted, share counted by hand today, minutes per reel, labour cost, X3100 handling minutes and the quoted price - and shows hours freed, net monthly value and the payback period. Southern Machinery adds no savings figure of its own.

Review the case six months after installation with real data from the counter's daily records. A payback case that is checked against actual counts becomes the template for the next investment.

Ask for a quotation with your volume and options, then put the price into the calculator. Write to info@smthelp.com or WhatsApp +86 13602562576.

ARTICLE 07Inventory Accuracy as a Weekly Number

Ten random reels a week tell you whether MES can be trusted.

Full articles are in English. The summary above carries the argument in your language.

Ask a warehouse lead how accurate the stock is and you get an adjective: good, mostly fine, better than last year. Ask the planner who just ran out of a part and you get a different adjective.

Inventory accuracy is rarely measured between audits, so it drifts silently. By the time the annual count reveals the gap, the cost has already been paid in shortages, overbuying and write-offs. Without a weekly number, nobody can tell whether a process change helped.

Make it a weekly number. Every Friday pick ten random reels in stock, recount them and compare with the system. Record matches out of ten and the cause of every mismatch. Over a quarter the trend is clear, and each cause points to a step in the process that needs fixing.

With the X3100 the weekly check takes minutes instead of an afternoon: ten reels are three X-ray shots, each count is matched to its reel ID from the label, and the daily TXT, CSV or XLS records give you the reference to compare against MES.

Post the weekly figure where the warehouse and the planners both see it. When it holds at ten out of ten, MES can be trusted for planning; when it slips, the cause column says where to look.

Want help setting up the weekly check and the data link? Send your MES name and reel volume to info@smthelp.com or WhatsApp +86 13602562576.

ARTICLE 08What to Send for an X3100 ROI Proposal

Five facts get you a version, an interface plan and a quotation.

Full articles are in English. The summary above carries the argument in your language.

An enquiry arrives: 'Please quote your X-ray counter.' It is the slowest way to get a useful answer, because the right version, the interface and the ROI all depend on facts the enquiry does not contain.

Without volume and data facts, a supplier can only send a brochure and a price, and the buyer still cannot tell whether it pays back or fits the warehouse. Weeks pass in clarification emails while reels keep going back to the shelf uncounted.

Send five facts with the first message: reels counted or returned per month and the reel sizes; your current counting method and minutes per reel; the smallest and hardest part numbers and packages; your MES, ERP or WMS with a photo of the current reel label; mains voltage, floor space and the route into the building.

With those facts Southern Machinery can choose between the offline X3100 (four reels per shot, reels 4 - 17 inch, trays, tubes, bags and loose parts) and the X3100 Inline (automatic loading, counting, labelling and unloading), plan the MES sync and quote. You put the quoted price into the calculator on this page and see the payback with your own numbers.

Keep the five facts in one document and update it each year. It becomes the brief for every warehouse automation project, not only this one.

Send the five facts to info@smthelp.com or WhatsApp +86 13602562576, or use the form on this page.

After the counter lands

What Southern Machinery does after delivery

🛠️

Installation and set-up

Set-up by our engineers or remote guidance, including barcode type, label template and flat panel settings.

🧑‍🏫

Operator training

The 30-minute route on this page plus the X-ray safety rules, delivered with the manual.

🔗

MES / ERP / WMS integration

We agree the data fields, file format and label layout with your IT team before shipment, so the sync works on day one.

🏭

Whole-line support

Reel storage, feeders, splicing, board handling and full SMT / THT lines.

FAQ

Questions buyers ask about ROI, accuracy and MES

How is the X3100 return on investment calculated?
From your own numbers: reels counted per month, the share counted by hand or tape-wheel today, minutes per reel and your labour cost, minus the operator time at the X3100. The quoted price divided by the net monthly value gives the payback. Line stops avoided and reconciliation time saved come on top. Southern Machinery publishes no savings percentage.
Is the 99.99 % accuracy guaranteed for my parts?
99.99 % is the brochure and manual figure with 0201 chips as the example, and the barcode misread rate is stated as no more than 0.01 % in the same example. Accuracy depends on part type, package and image settings, so we recommend a trial count with your own reels before you order.
How does the MES sync work?
The 20-megapixel camera reads every barcode on the reel label, the software matches the count to that reel ID and, with the MES / ERP button active, sends the result to MES, ERP or WMS. Records are also kept in daily TXT, CSV or XLS files. Data fields and file format are agreed with your IT team per order.
How fast does it count?
The offline X3100 counts four reels in 6 - 10 seconds for chip 0201 parts, with a cycle of no more than 10 seconds per count; one brochure table states 6 - 8 seconds. The Inline version needs 9 - 15 seconds per reel but loads, labels and unloads by itself.
Is it safe to have an X-ray machine in the warehouse?
The radiation test value is below 1 µSv/h. The cabinet has two door interlocks, a double safety circuit, over-voltage and over-current protection and an emergency stop. Only trained staff should operate it, and local registration rules for X-ray equipment apply in your country.
What does the inspection function do?
The same X-ray tube and flat panel can show a live image of an assembly, for example broken wires in a cable or solder wires in a speaker, as in our video. One click switches the software back to counting. For BGA void analysis we offer the dedicated SM-X3000A inspection machine.
What does it cost and how long is delivery?
Price, lead time, warranty and payment terms are quoted for your version and options and are not published on this page. Send your daily reel volume, reel sizes, smallest part and MES system for a quotation.
What power and space does it need?
AC 110 - 220 V, 50 - 60 Hz, 1200 W, 450 kg. The brochure gives 949 x 1456 x 1934 mm with printer and the operation manual 950 x 1460 x 1960 mm, so we confirm the exact size with your order. The Inline version measures 3087 x 1194 x 1957 mm and weighs 1500 kg.
Contact

Send your reel numbers and we return an ROI-ready proposal

Tell us your reels per month, how you count today and how long it takes, your smallest part and the MES or WMS you use. A photo of your current label lets us prepare the MES sync and the printout.

X3100 X-ray counter ROI enquiry

This form opens your own mail client. Nothing is sent from the page.