Southern Machinery Get a Quote
New model · Bulk THT LED

S3030ABulk LED Radial Insertion Machine

Built only for loose through-hole LEDs. Three bowl feeders run red, green and blue on their own, every LED is checked for polarity and lit up before insertion, and the head inserts at over 10,000 CPH.

 3 bowls · 3 colours · 2.5 mm lead span
S3030A bulk LED radial insertion machine on the S3000 radial platformS3000 radial platform — base of the S3030A
>10,000CPH actual insertion speed
3bulk LED bowl feeders, one per colour
2.5 mmlead span, R / G / B LEDs
100%polarity + function check before insertion
Product highlights

Four things only a bulk LED inserter does

Loose LEDs in a vibratory bowl feeder

Bulk THT LEDs only

Loose LEDs go straight into the bowls. No ammo packs, no taped LEDs.

Three bulk LED bowl feeders with tracks

3 bowls, 3 colours

Red, green and blue each have their own bowl, track and sensors.

LED polarity check and 180 degree correction station

Polarity + function check

Turned 180° when reversed; lit and checked for brightness and colour.

LEDs inserted into a dense PCB array

Over 10,000 CPH

Actual insertion speed on the proven servo + lead screw head.

Bowl 1 — Red2.5 mm lead span LEDs, own track and sensors
Bowl 2 — GreenIndependent feeding, no colour mix-up
Bowl 3 — BlueEach position gets its colour from the program
How it works

From a bag of LEDs to a finished LED board

Every LED passes two checks before it reaches the insertion head. Reversed LEDs are turned; dead, dim or wrong-colour LEDs are rejected.

  1. 01

    Bowl feeder

    Loose LEDs of one colour vibrate into single file

  2. 02

    Sensors

    Track sensors keep the line full and steady

  3. 03

    Polarity check

    Wrong way round? Turned 180° and checked again

  4. 04

    Function test

    Light-up, brightness and colour checked; bad LEDs rejected

  5. 05

    Servo + cam transfer

    Good LEDs loaded onto the chain

  6. 06

    Insertion head

    Servo + lead screw head inserts at 0–360°

  7. 07

    Cut & clinch

    Leads cut and bent under the PCB

Servo and lead screw insertion head

Servo + lead screw head

Ball screw + spline shaft, insertion direction 0–360° in 1° steps, cut and clinch 10–15° under the board.

200 x 200 mm PCB with auto inserted LEDs

Vision + MARK correction

The camera reads PCB marks and corrects every hole position; programs come in by USB as Excel files.

Specifications

S3030A technical data

Platform values come from the S3000 radial inserter the S3030A is built on. Items marked "To be confirmed" depend on your configuration.

ParameterS3030ASource
Component typeBulk (loose) THT LEDs, 2-lead radialModel spec
LED coloursRed / Green / Blue, one bowl feeder per colourModel spec
Lead span2.5 mm (2.54 mm pitch LEDs)Model spec
Bulk feeders3 vibratory bowl feeders, independent feedingModel spec
In-line checksPolarity direction + function (light-up, brightness, colour)Model spec
Polarity correctionAuto 180° turn, then re-checkVideo verified
Bad-part handlingFailed LEDs rejected before insertionVideo verified
Actual insertion speed> 10,000 CPHModel spec
Insertion direction0–360°, 1° incrementsS3000 platform
PCB size50 × 50 mm to 400 × 300 mm (larger on request)S3000 platform
PCB thickness0.79–2.36 mmS3000 platform
Lead cut length1.5 ± 0.3 mm (short blade) / 2.0 ± 0.3 mm (long blade)S3000 platform
Clinch angle10–15°, adjustableS3000 platform
Hole correctionMachine vision, multi-point MARK correctionS3000 platform
Drive / controlAC servo, bus control, absolute encodersS3000 platform
ProgrammingUSB input, Excel program fileS3000 platform
Board handlingAutomatic board loading and unloadingS3000 platform
Insertion defect rate< 500 PPM (S3000 platform)S3000 platform
Air supply0.6–0.8 MPa, about 0.2 m³/minS3000 platform
Power220 V AC single phase, 50/60 HzS3000 platform
Footprint / weightConfirm per configuration (bowl feeder layout)To be confirmed

S3000 taped radial vs S3030A bulk LED

S3000 Radial InserterS3030A Bulk LED Inserter
Parts fedTaped radial parts (caps, transistors, LEDs, fuses...)Bulk (loose) THT LEDs
Feeder10 tape stations (14 optional)3 vibratory bowl feeders, R / G / B
Lead span2.5 / 3.5 / 5.0 / 7.5 / 10.0 mm2.5 mm
Part check—Polarity + light-up / brightness / colour
PolaritySet by the tapeDetected and auto-corrected 180°
Actual speed10,000 CPH> 10,000 CPH
Taped LEDs neededYesNo — loose LEDs go straight into the bowl
PlatformServo + lead screw head, MARK visionSame S3000 platform
Applications

Made for LED-dense THT boards

▦

LED display & signage

Outdoor modules, scoreboards, message boards

◉

Traffic & signal lights

Dense round LED arrays like the 200 × 200 mm board

☀

LED lamps & lighting

Bulbs, downlights, decorative RGB lighting

▣

Automotive & indicator

Tail-light boards, dashboards, status panels

▤

Appliance & control panels

Indicator LEDs on power and control boards

✦

Amusement & decoration

RGB colour boards, holiday and stage lighting

CPH & efficiency

Over 10,000 LEDs per hour, actual

Compare with manual insertion and estimate your own board.

Manual insertion, one operator (typical)1,500–2,000 / h
S3030A actual insertion speed> 10,000 / h
Example: 200 × 200 mm LED boardValue
LEDs per board250
Insertion time at 10,000 CPH90 s
Boards per hour (insertion only)about 40
One operator at 2,000 / h7.5 min per board

Example calculation. Real output depends on hole spacing, board loading and colour changes.

Cycle-time estimator

90 sinsertion time / board
640boards / day
5.0operators to match by hand

Insertion time only; board transfer adds a few seconds per board. Send your insertion file for an exact figure.

Videos

See the bulk LED feeding run

RGB bulk LED bowl feeders
Polarity check and 180° correction
LED radial insertion on a dense board
Operation

Changeover in six steps

  1. Load the new program from USB (Excel file)
  2. Teach or confirm the MARK points with the vision camera
  3. Assign colours: red, green and blue bowl for each LED position
  4. Fill the bowls with loose LEDs
  5. Run a first board and check polarity and light-up results
  6. Start production; board loading and unloading run automatically
Maintenance

Simple upkeep

Every shiftClean the bowl feeders and tracks; empty the reject bin; check air pressure 0.6–0.8 MPa
WeeklyClean the polarity / test sensors and camera window; check cutter blades and clinch parts
MonthlyLubricate lead screws and guides; check chain tension and belts; back up programs
Every 6 monthsFull calibration of axes and vision; check servo cables and air filters
Drawer-style control box
Service

Support from our Shenzhen factory

Free demo & live video

Watch your own LEDs and PCB run before you decide

Installation & training

On-site or remote set-up, operator and engineer training

24/7 worldwide support

Remote diagnosis, WhatsApp / video support

Spare parts from Shenzhen

Wear parts compatible with Universal radial machines

3D drawings & animations

Training material that shows how the machine works

Custom solutions

Feeder and fixture changes for special LED boards

FAQ

Questions buyers ask

Do I need taped LEDs?

No. The S3030A takes loose (bulk) THT LEDs straight into its three bowl feeders, so you can buy LEDs in bags instead of ammo or tape.

Can it run three colours on one board?

Yes. Each bowl feeder holds one colour (red, green or blue) and feeds independently, so the program places each colour where it belongs.

How does it make sure the polarity is right?

Every LED is checked for polarity before insertion. If it is the wrong way round, it is turned 180° and checked again.

Does it test the LEDs?

Yes. Each LED is lit and checked for light-up, brightness and colour. LEDs that fail are rejected before they reach the board.

How fast is it?

Actual insertion speed is over 10,000 CPH. Real output depends on the board layout and travel between holes; send us your board file for a cycle-time estimate.

Which LED sizes can it handle?

It is built for 2-lead THT LEDs with 2.5 mm lead span. Send us your LED datasheet or samples and we confirm the bowl and track tooling.

What PCB sizes fit?

From 50 × 50 mm to 400 × 300 mm, 0.79–2.36 mm thick. Larger boards can be built on request.

How do we program a new board?

Import the insertion coordinates from an Excel file by USB, teach the MARK points and assign a colour per position.

Inquiry

Send your LED board for a free evaluation

Tell us about your LEDs and PCB. We reply with a cycle-time estimate and a configuration proposal.

✉️ info@smthelp.com · jasonwu@smthelp.com

💬 WhatsApp +86 136 0256 2576

🏭 Shenzhen, China · www.smthelp.com

Chain feed to the insertion head
WhatsApp us
Thank you — your email app is opening with your inquiry to info@smthelp.com. If it does not open, write to us on WhatsApp +86 136 0256 2576.

S3030A: bulk LEDs in, checked LEDs on the board.

Get a Quote
WhatsApp